Jump to content

Recommended Posts

Posted

Hi all,

 

Although simple, this is a small walkthrough mostly about not discarding a Seiko chronometer.

The movement was available new so in the future I may tackle the old movement to try and make it tick again.

This one was fitted with the brand new movement as per specs.

 

Quick Seiko "Flight" watch restoration:

 

Original from the bay:

post-253-0-28062000-1424797873_thumb.jpg

Taking it appart (case) mostly:

post-253-0-71759100-1424797889.jpg

After some "fairy" or "Downy" depending of the part of the world...and rodico. Crystal Gasket already on case.

Note that chapter ring goes in its groove under this gasket and then the crystal is fitted. Old pushers to be restored:

post-253-0-55423900-1424797888_thumb.jpg

New crystal, crystal gasket (not shown), and case gasket:

post-253-0-12904300-1424797877_thumb.jpg

Pushers restored with new (double) gaskets:

post-253-0-12464500-1424797824_thumb.jpg

Lube everything:

post-253-0-29222800-1424797886_thumb.jpg

Case with restored pushers in place:

post-253-0-35013700-1424797875_thumb.jpg

Quartz Movement fitted (new V657 as per specs) and case gasket lubed:

post-253-0-28673800-1424797883_thumb.jpg

THE WATCH, with new (recovered) hands (other similar model) that I liked better:

post-253-0-07079300-1424797838_thumb.jpg

On the wrist:

post-253-0-09413500-1424797880_thumb.jpg

Enjoy!

Cheers,

Bob

  • Like 1
Posted

Thank for your encouraging remarks guys, I appreciate that, being kind of new to the watchmaking world and all!

 

I will try and fix the old movement (I got some spares) and if successful, I'll add the walkthrough too. (I still have a NH36 I want to document here so it might take a little) At about US$50 new and hard to find, it is a good idea to try and fix the old movement, I think.

 

On a side note, I'd like to know more about this watch. Is it part of the "Flightmaster" line of Seikos? Thanks in advance.

 

Cheers,

 

Bob

Posted

Thank you Mark! Coming from you I feel great! Your site, advise and videos are making my progress possible!

 

Cheers,

 

Bob

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hi folks, I'm doing some homework on getting a watchmaker's lathe, and it's clear I have a lot to learn. But I know one goal: I want to be able to fabricate wheels, which would require an indexing capability. I know how to use large lathes- like, giant metal lathes- but my experience is a few decades old now (but you never forget the smell of the metal cutting oil). So I'm looking to learn anew, and have a goal to get to a point where I can fabricate some basic watch parts. I also have no specific timeframe and want to do this right, so I'll be patient and learn what I need to before spending the money. I know I'm not going to get anything for a pittance, but I'm also not really able to put together the scratch for a $5-$10k lathe. What's out there for a hobbyist that can either handle some fabrication out of the box or can be relatively easily made to do so? Thanks!  
    • Hello and welcome to the WRT forum.   This usually points to broken balance pivot.  Though a watch in need of clean & lube can do the same. Easiest diag would be to  see if balance pivot doesn't stay in hole jewel of the setting, when you lift one side of balance rim with an oiler or gently with pair of tweezers. Another would be to detach balance complete from the cock and take a look at pivot under high maginfication.  Regs 
    • Ahhh, yes.  I hadn’t thought of that.  I’ve serviced quite a few of these and the first time I didn’t realise it was a ships strike pattern!  Ha ha, confused me totally until I realised.
    • Hello and welcome from Leeds, England. 
    • Hi Mike, I did, thanks. Found this clip that was really helpful:   It says Seth Thomas but it's actually the same Hermle I've been working on. I'd had it working correctly all along but hadn't noticed that the lever with the sprung end stops the hammer a bit short of the bell on the second ding at the end of the half-past sequence. If only I'd put the bell on when testing, rather than just looking at the hammer, my ears would have told me it was working,  even if my eyes didn't!  
×
×
  • Create New...