Jump to content

Le-Coultre Futurematic

Geo

By Geo
in Your Watch Collection

 Share

Recommended Posts

Geo Distinguished Member

Geo

Posted
Posted

I have a love of bumper automatics, and have a few from different manufacturers in my collection. The Holy Grail that has eluded me for a long time is the Le Coultre Futurematic. This has now been put right by my latest acquisition from Germany.

post-124-0-48063100-1434548385_thumb.jpg

post-124-0-12194000-1434548414_thumb.jpg

This Futurematic has a complicated, but very well made calibre 497 movement and is keeping excellent time, about +3 seconds a day on the wrist. It also produced a nice clean graph with no beat error on my Timegrapher. I will service it sometime in the future and post an article about it. The only thing I have done to it is re-finish the original crystal and give the slightly worn gold finish a light polish and fit a new strap. I'll do a proper job later when I service it.

Unusual features are:-

post-124-0-11297400-1434548434_thumb.jpg

post-124-0-57655500-1434548459_thumb.jpg

The watch has no visible crown, it is hidden on the back of the case in the form of a flat serrated button. To set the watch, slide the button towards the middle of the watch then rotate it to set the time. There is a built in hacking lever so it is possible to set the time to the exact second.

The watch cannot be wound by the button, just set the time give the watch a couple of shakes and wear it.

post-124-0-34144000-1434548478_thumb.jpg

Manual type mainspring that has no facility to let it slip when fully wound like other automatic watches. When fully wound, a latch comes into play and locks the bumper rotor preventing it from moving. When the spring unwinds slightly, the latch releases and allows the rotor to swing again. The good thing about this system is the rotor only moves when required and cuts down on bearing wear.

Another strange feature of the spring setup is it is pre-tensioned with one and half turns of preload when run down. This ensures an immediate start up as soon as the rotor moves, negating the need to give the watch a good shake before wearing it.

post-124-0-10617000-1434548501_thumb.jpg

There is a power reserve indicator at the three o’clock position on the dial that rotates clockwise when winding. When fully wound, the indicator just touches the bottom of the gold quadrant, and when run down, the hand is in the vertical position at the beginning of the red quadrant. Power reserve is 27 hours.

Just as an aside, when re-casing the movement the matt black dial was a sod to clean properly. After using the puffer I noticed that there were still some tiny specks on the surface. They are easily removed with the lightest touch of the Jewel Picker Upper!

I hope you found this interesting.

  • Like 4
WillFly Distinguished Member

WillFly

Posted
Posted

That's an amazing watch - love it! A gorgeous dial and a very interesting movement - what more could an addict want...

  • Like 1
Marc Distinguished Member

Marc

Posted
Posted

Nice catch Geo,

 

both technically and aesthetically that one ticks (and tocks!!!) all of the boxes.

  • Like 1
Jim WRT Addict

Jim

Posted
Posted

Great looking movement   from the photo the hairspring looks strange?   is it just the angle?   Just wondering I have not serviced that particular JL movement yet

 

Sincerely,

Jim

  • Like 1
Geo Distinguished Member

Geo

Posted
  • Author
Posted

I see what you mean Jim. It is probably is just an aberration due to the lens and the angle the photo was taken. The watch starts easily and is holding excellent time, so I don't think anything is amiss. When I strip I get around to servicing it, I'll have a closer look.

  • Like 1
  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Kalanag
      Replacing crystal, do I need a bezel tool?

      By Kalanag · Posted

      From what I see, the crystal is made of mineral glass and is secured to the bezel with a sealing ring. If you might want to replace the crystal without removing the bezel or the movement, I think it's possible, but risky. You have to suck out the old crystal without breaking it into tiny particles. I would not do that.
    • Sebastiaan
      New hobbiest to watch repair from the Netherlands

      By Sebastiaan · Posted

      Hello Everyone, A short message to introduce myself. I'm Sebastiaan (50) from the Netherlands and have always been interested in watches. My two kids are at the end of their teens years and so I have more time to start a hobby.  Working on watches was something I always wanted to learn. So I recently started the watchfix repair course. Currently watching level 3. My short term goal is to be able to service the watches we (Myself, my wife and kids) own. I own a manual Omega Geneve from 1974, a small microbrand watch with a NH35 and a wittnauer bumper from 1940's. My wife owns an Oris, Seiko 5 with 7s26c and my son a seiko alpinist sarb017 and sports 5 with 4R36. So enough to learn on the short term..  Looking forward to talking to all of you and enjoying the watch hobby together. Greetings Sebastiaan
    • BlueHarp
      Longines with 25.17 caliber

      By BlueHarp · Posted

      It works quite well. The only strange thing is that it loses 2/3 mn per day whereas the measurements indicate that it is fast by 1/2 mn. Maybe something wrong with the gear mechanism ...
    • rehajm
      Longines with 25.17 caliber

      By rehajm · Posted

      Unfortunate…but you clearly have a Longines branded movement with a year 1936 serial consistent with the caliber. I checked the case maker of the last few Longines I worked on… …same as your watch, so certainly you have grounds to honestly describe your watch as a Longines cal 25.17 tank with unbranded dial…and given the modesty of the watch IMO the Longines authentication wouldn’t dramatically alter the value, if that’s what you are hoping…as nucejoe suggests the value will mostly be determined by how well it runs…
    • VWatchie
      Replacing crystal, do I need a bezel tool?

      By VWatchie · Posted

      It's difficult to tell, but my guess is it just looks like it has a bezel. Once you have removed the movement, you should be able to tell. Either way, I think you should be able to press out the old crystal from the inside as long as you have a die that properly supports the area around the crystal. So, take it a part first and then assess if any additional tools or actions are needed. Let us know how you do!  
×
×
  • Create New...