Jump to content

How To Release Tension From The Mainspring

rogart63
 Share

Recommended Posts

Geo Distinguished Member

Geo

Posted
Posted

The pictures a bit fuzzy Roger, but remove the magic finger and pinion that it drives by removing the large bridge on top of the movement. Now get a good fitting screwdriver and turn the barrel slightly to release the click. Hold the click out of engagement with a piece of pegwood then let the screwdriver rotate while controlling it with your fingers until there is no tension left in the spring.

  • Like 2
rogart63 Distinguished Member

rogart63

Posted
  • Author
Posted

Can't take the mainspring barrel apart ? Is it ment to be taken apart . Bad pictures i now but can't make it focus any more then that .

 

post-644-0-48820500-1434632736_thumb.jpgpost-644-0-72191800-1434632743_thumb.jpg

 

 

Marc Distinguished Member

Marc

Posted
Posted

From memory Seiko barrels are a little different to the Swiss offerings but the following could be mistaken.

Look at the barrel edge on.

You should see a thin line that runs around the circumference of the barrel half way up its height; this is the join between the barrel and its lid.

using a single edged razor blade push the blade into this joint and work it around the barrel; the two halves should start to separate. 

Repeat with successively wider blades until the two halves can be separated by hand.

  • Like 1
Geo Distinguished Member

Geo

Posted
Posted

To open the barrel, I usually position the barrel as in the first picture, on a hard surface. Open your tweezers wide and locate the barrel between the blades then press down hard on the tweezers and the barrel should pop open.

evn137BANNED Member

evn137BANNED

Posted
Posted

How easy everything is when you now how to do it . Thanks @Marc

That's why I enjoy this forum. Lots of technical help available, even sourcing material.

For newbies like me it reassuring.

Cheers!

Mark Distinguished Member

Mark

Posted
Posted

To open the barrel, I usually position the barrel as in the first picture, on a hard surface. Open your tweezers wide and locate the barrel between the blades then press down hard on the tweezers and the barrel should pop open.

 

 

Not so easy with a Seiko barrel :)

 

Best to use a razor blade very carefully so as not to damage the teeth or burr the metal so a very sharp razor is required. 

Not sure what the official Seiko way of doing it is but this method has served me well over the years.

 

The reason is that the barrel cap is similar to the Valjoux 7750 but worse, the lip goes right down to the barrel teeth.

 

**Edit** Just notice that Marc has already provided this info - apologies to Marc 

Geo Distinguished Member

Geo

Posted
Posted

Ah, that must be different to the last Seiko I worked on, as it opened as I described. I'll file this in the memory bank just in case I come across one like this. Thanks Mark! :)

Blacklab Distinguished Member

Blacklab

Posted
Posted

Tend to do the same as Geo on the Seiko barrels, but I use cheapo brass tweezers.

 

One question though how do you let the spring down on a Smiths?:

post-80-0-59369300-1435441806_thumb.jpg

no screw to hold the tension.

Geo Distinguished Member

Geo

Posted
Posted

Turn the crown slightly in the winding direction to allow you to hold the flat click spring back with back with a piece of pegwood. Now let the crown spin under control between your fingers to let the spring unwind.

  • Like 2
Blacklab Distinguished Member

Blacklab

Posted
Posted

Cheers Geo. Now why-o-why-o-why didn't I think of that. Beachy Head here I c

                                                                                                                            o

                                                                                                                            m

                                                                                                                            e

                                                                                                                         

                                                                                                                            splat!

Geo Distinguished Member

Geo

Posted
Posted

We all have these wee moments BL.

I like a nice Smiths and look forward to seeing the end result. :)

 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Kalanag
      Replacing crystal, do I need a bezel tool?

      By Kalanag · Posted

      From what I see, the crystal is made of mineral glass and is secured to the bezel with a sealing ring. If you might want to replace the crystal without removing the bezel or the movement, I think it's possible, but risky. You have to suck out the old crystal without breaking it into tiny particles. I would not do that.
    • Sebastiaan
      New hobbiest to watch repair from the Netherlands

      By Sebastiaan · Posted

      Hello Everyone, A short message to introduce myself. I'm Sebastiaan (50) from the Netherlands and have always been interested in watches. My two kids are at the end of their teens years and so I have more time to start a hobby.  Working on watches was something I always wanted to learn. So I recently started the watchfix repair course. Currently watching level 3. My short term goal is to be able to service the watches we (Myself, my wife and kids) own. I own a manual Omega Geneve from 1974, a small microbrand watch with a NH35 and a wittnauer bumper from 1940's. My wife owns an Oris, Seiko 5 with 7s26c and my son a seiko alpinist sarb017 and sports 5 with 4R36. So enough to learn on the short term..  Looking forward to talking to all of you and enjoying the watch hobby together. Greetings Sebastiaan
    • BlueHarp
      Longines with 25.17 caliber

      By BlueHarp · Posted

      It works quite well. The only strange thing is that it loses 2/3 mn per day whereas the measurements indicate that it is fast by 1/2 mn. Maybe something wrong with the gear mechanism ...
    • rehajm
      Longines with 25.17 caliber

      By rehajm · Posted

      Unfortunate…but you clearly have a Longines branded movement with a year 1936 serial consistent with the caliber. I checked the case maker of the last few Longines I worked on… …same as your watch, so certainly you have grounds to honestly describe your watch as a Longines cal 25.17 tank with unbranded dial…and given the modesty of the watch IMO the Longines authentication wouldn’t dramatically alter the value, if that’s what you are hoping…as nucejoe suggests the value will mostly be determined by how well it runs…
    • VWatchie
      Replacing crystal, do I need a bezel tool?

      By VWatchie · Posted

      It's difficult to tell, but my guess is it just looks like it has a bezel. Once you have removed the movement, you should be able to tell. Either way, I think you should be able to press out the old crystal from the inside as long as you have a die that properly supports the area around the crystal. So, take it a part first and then assess if any additional tools or actions are needed. Let us know how you do!  
×
×
  • Create New...