Jump to content

Bench light ?

ianrichards
 Share

Recommended Posts

ianrichards Member

ianrichards

Posted
Posted

Good evening folks. 
Some advice on a suitable bench light would be greatly appreciated. 
I’m based in the UK and have looked at Cousins range and I’m not sure what I should be looking for. 
Should I go for a combined magnifier/lamp or just a lamp ? Dimmable or not ?

My current lighting is dreadful so definitely needs sorting. 
TIA

tomh207 Distinguished Member

tomh207

Posted
Posted

Ian, I would go for a bench light, I have the combo magnifier/light version and find it pretty useless for watch work. It gets used now only as a light and very occasionally to inspect a case or bracelet. Only my thoughts and opinion.

 

Tom

  • Like 1
  • Thanks 1
Waggy Distinguished Member

Waggy

Posted
Posted
11 minutes ago, tomh207 said:

I have the combo magnifier/light version and find it pretty useless for watch work.

I second that, I ended up donating mine to Mrs W's quilting room and opted for the cousins bench light which I 100% recommend:

image.thumb.png.90d73f68c88cd384557bcb8816202449.png

It's expensive, but throws out a huge amount of light - I'm sure the occasional 747 wanders off course when i switch it on. Being LEDs it doesn't cook you either. It is dimmable and you can change the type, (blue/daylight, warm/yellow etc.) so suit your needs also it clamps to the desk so frees up valuable desk real-estate! One of those few tools you end up saying "how did I manage without it!?!?"

  • Thanks 1
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
On 12/3/2023 at 9:15 PM, ianrichards said:

Good evening folks. 
Some advice on a suitable bench light would be greatly appreciated. 
I’m based in the UK and have looked at Cousins range and I’m not sure what I should be looking for. 
Should I go for a combined magnifier/lamp or just a lamp ? Dimmable or not ?

My current lighting is dreadful so definitely needs sorting. 
TIA

Same as Tom i have a big magnifying glass/light combo, use it quite a bit for case polishing and initial decasing and some disassembly. I increase magnification with it by using +4 reading glasses, for anything more detailed i pop a x5 loupe on the glass of the magnifier . It gave enough magnification to rough out an 8mm setting lever. But for bench lighting i have a diffused 2' fluorescent light ( £10 ) mounted under a shelf on the general workbench and a couple of anglepoise lights on the watchbench. One is really small  but i can bring it right up to the watch and direct light inside it.

  • Thanks 1
linux WRT Addict

linux

Posted
Posted

I've had one of those circular magnifier lights but was disappointed in it, so I went to a couple of the artists clamp-on lights that I put 100 W equivalent LED bulbs in.  That gave me good light but I still needed more direct light right over my work pad so I bought a nice LED desk lamp similar to the one shown above from Cousins.  It clamps to the edge of the work bench and is tall enough to where the vertical arm doesn't get in the way.

 

 

20231207_153355.jpg

Also, as you can see, my bench is in the garage and my biggest challenge is dust, hence the glass baking pan upside down of the work pad.  Since that picture, after looking for better non-glass alternative I ordered a custom plex display case and just received it.  I probably could have made it 3" high rather than 6", but being a rookie I still lay things out on the pad as I disassemble because and leave them there overnight.

20231210_155330.jpg

  • Like 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • HectorLooi
      Hour hand won’t go past certain spot when adjusting time forwards

      By HectorLooi · Posted

      If the watch is new, just return it to the seller for a refund or replacement.
    • Randy55
      Hour hand won’t go past certain spot when adjusting time forwards

      By Randy55 · Posted

      Keevo, Welcome to the group ! I'm thinking that you have some damage to the hour, and/ or minute wheel. Possibly just a bent, otherwise damaged, or missing tooth.   Your photo didn't post that I can see. I think you'll have to open it to start really finding the issue. Best, Randy
    • Neverenoughwatches
      Diy rotary cleaning machine

      By Neverenoughwatches · Posted

      An industrial break cleaner , like Holts does a good job of rinsing off paraffin 
    • mikepilk
      Cap jewel with what looks like a circular engraving around the edge

      By mikepilk · Posted

      In cap jewels on several watches I have serviced over the years. I've recently serviced a couple of Longines movements where the cap jewels were colourless. They are a real pain. Without colour they disappear when immersed in any liquid for cleaning 😲 Not necessarily. Cousins do a 10ml bottle for £26 which will last me for years. That's just half the price of a simple Bergeon silicone cushion, so not too expensive 🤣
    • BobG
      Etachron regulation system

      By BobG · Posted

      I wanted to post an update as I have two movements running really well now, 230-250 amplitude , 0.5 and under beat error, and +/-8 seconds or so. I removed the hairspring assembly in order to start over and noticed that the terminal curve between the stud and regulator arm was distorted. The stud was lower than it should be. I massaged the curve to look pretty good and reinstalled it. I followed Alex's video advice, best I could with 10x magnification, and with the regulator arm set in the middle of the curve I adjusted the stud so the spring was centered. I then made sure I could move the regulator arm the entire terminal curve without upsetting the coils. I then put it back on the Timegrapher and began closing down the regulator pins until I saw a change in amplitude which means to me that the pins were now pinching the spring. I opened them slightly and it looks good except I have a 0 on dial down, +3 on dial up but -16 on crown down.  I'm a bit stuck on how to adjust out the positional error. I also noticed a drop in amplitude, 180-200 on crown down. In the other video link I posted at about minute 26 if I remember he adjusts out positional error by manipulating  the regulator pin gap. With crown down the hairspring falls away from the pin and the rate slows so he closes the pins a bit to keep them tighter in crown down position. That means the spring is tighter on dial up as well but then he moved the regulator arm to slow the movement.  There must be some Seiko experts here that have some methods for dialing out positional errors. 
×
×
  • Create New...