Jump to content

Rotary tool

ClaudioCavalli
 Share

Recommended Posts

ClaudioCavalli Member

ClaudioCavalli

Posted
Posted

The next tool on my list is a rotary tool to fix a couple of scratched up crystals.  I've been reading up on watch forums on what tool people use and I see a lot of people use Dremel and Proxxon rotary tools (Did you guys see their mini lathes?  Wow!!).  However, I see that their minimum speeds are 2,000 rpm or so.  Isn't this too much for polishing?  No room for error?  I was looking at something like a Grobet rotary rool (See here) but they do not have specs for lowest speed on their web site.  However, similar tools on Amazon go down to 500 rpm.  Does anybody know if the Grobet goes down to 500 rpm as well?  Wouldn't this speed be better and more forgiving for polishing plexiglass crystals?

thank you

claudio

HectorLooi Distinguished Member

HectorLooi

Posted
Posted

That looks like a Chinese made Foredom motor. If it is a Chinese made foot pedal, you will have problems with it in about a month's time. 

But no big issue as you can build your own benchtop speed control quite easily.

HectorLooi Distinguished Member

HectorLooi

Posted
Posted

The Chinese made motors are pretty good too. I've been using one for the last 6 months. 

I think the electronic foot pedals for sewing machines may work as a substitute but it would require a bit of rewiring. The problem with the Chinese Foredom pedal is that the potentiometer has a very short travel of about 1 cm only. The sewing machine pedal has a potentiometer at least twice as long.

Flexshaft motors can go down to quite a low speed but it wouldn't have much torque at these speeds.

Polishing is a lot of trial and error. The required speed depends on the material being polished, the polishing compound used and the type of polishing tool used. (eg. Silicone rubber abrasives, soft felt, hard felt, wool mop, muslin mop, etc)

The amount of pressure used also depends on the above variables. Some require high pressure, others require a light touch.

It's a science as well as an art. Have fun! 😉

  • 3 weeks later...
VWatchie Distinguished Member

VWatchie

Posted
Posted
On 12/26/2023 at 5:41 AM, ClaudioCavalli said:

I've been reading up on watch forums on what tool people use and I see a lot of people use Dremel and Proxxon rotary tools (Did you guys see their mini lathes?  Wow!!).

I haven't had the best of experiences with a rotary tool for polishing.

I've had a lot more success using a dedicated polishing machine so I'd recommend that.

 

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • HectorLooi
      Hour hand won’t go past certain spot when adjusting time forwards

      By HectorLooi · Posted

      If the watch is new, just return it to the seller for a refund or replacement.
    • Randy55
      Hour hand won’t go past certain spot when adjusting time forwards

      By Randy55 · Posted

      Keevo, Welcome to the group ! I'm thinking that you have some damage to the hour, and/ or minute wheel. Possibly just a bent, otherwise damaged, or missing tooth.   Your photo didn't post that I can see. I think you'll have to open it to start really finding the issue. Best, Randy
    • Neverenoughwatches
      Diy rotary cleaning machine

      By Neverenoughwatches · Posted

      An industrial break cleaner , like Holts does a good job of rinsing off paraffin 
    • mikepilk
      Cap jewel with what looks like a circular engraving around the edge

      By mikepilk · Posted

      In cap jewels on several watches I have serviced over the years. I've recently serviced a couple of Longines movements where the cap jewels were colourless. They are a real pain. Without colour they disappear when immersed in any liquid for cleaning 😲 Not necessarily. Cousins do a 10ml bottle for £26 which will last me for years. That's just half the price of a simple Bergeon silicone cushion, so not too expensive 🤣
    • BobG
      Etachron regulation system

      By BobG · Posted

      I wanted to post an update as I have two movements running really well now, 230-250 amplitude , 0.5 and under beat error, and +/-8 seconds or so. I removed the hairspring assembly in order to start over and noticed that the terminal curve between the stud and regulator arm was distorted. The stud was lower than it should be. I massaged the curve to look pretty good and reinstalled it. I followed Alex's video advice, best I could with 10x magnification, and with the regulator arm set in the middle of the curve I adjusted the stud so the spring was centered. I then made sure I could move the regulator arm the entire terminal curve without upsetting the coils. I then put it back on the Timegrapher and began closing down the regulator pins until I saw a change in amplitude which means to me that the pins were now pinching the spring. I opened them slightly and it looks good except I have a 0 on dial down, +3 on dial up but -16 on crown down.  I'm a bit stuck on how to adjust out the positional error. I also noticed a drop in amplitude, 180-200 on crown down. In the other video link I posted at about minute 26 if I remember he adjusts out positional error by manipulating  the regulator pin gap. With crown down the hairspring falls away from the pin and the rate slows so he closes the pins a bit to keep them tighter in crown down position. That means the spring is tighter on dial up as well but then he moved the regulator arm to slow the movement.  There must be some Seiko experts here that have some methods for dialing out positional errors. 
×
×
  • Create New...