Jump to content

Cleaning/replacing/... a mainspring when still learning the ropes

LuigiMeister2800
 Share

Recommended Posts

LuigiMeister2800 Member

LuigiMeister2800

Posted
Posted

Hi everyone,

 

I wondered what your suggestions would be for someone starting out in the hobby.
 

When you haven't got mainspring winders yet do you best:

  • Just leave it in the barrel and assemble everything after cleaning the rest
  • Take it out, measure it and buy a new one (don't know if that's feasible for older watches)
  • Take it out, measure it and get an appropriate mainspring winder
  • Something else....

Thanks for the advice!

Malocchio WRT Addict

Malocchio

Posted
Posted

You could just buy a couple of the most common sizes. Best Chinese sets are allegedly good. Manual mainsprings are easy to wind by hand but automatic springs are trickier because of the bridle in the end. Buying new springs is also an option. 

  • Like 1
rossjackson01 Super WRT Addict

rossjackson01

Posted
Posted
23 minutes ago, LuigiMeister2800 said:

Hi everyone,

 

I wondered what your suggestions would be for someone starting out in the hobby.
 

When you haven't got mainspring winders yet do you best:

  • Just leave it in the barrel and assemble everything after cleaning the rest
  • Take it out, measure it and buy a new one (don't know if that's feasible for older watches)
  • Take it out, measure it and get an appropriate mainspring winder
  • Something else....

Thanks for the advice!

Watch the YouTube videos in how to hand wind.

It was 15 month before I obtained a set of winders. Only used them unsuccessfully since. 

watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi Maloccio has given the options, I still do it by hand, but if you are not sure just buy the winder to suit you purpose at the time. That way over time you will build a collection of the ones you use the most and. Not some ornaments which never get used.

Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
1 hour ago, LuigiMeister2800 said:

Hi everyone,

 

I wondered what your suggestions would be for someone starting out in the hobby.
 

When you haven't got mainspring winders yet do you best:

  • Just leave it in the barrel and assemble everything after cleaning the rest
  • Take it out, measure it and buy a new one (don't know if that's feasible for older watches)
  • Take it out, measure it and get an appropriate mainspring winder
  • Something else....

Thanks for the advice!

All depends what you are working on. If the right mainspring is available and the money to buy one each time isn't an issue then a new one would be the best option. Downside is you dont get to aquire the skill of winding mainsprings. Which eventually if you work on a lot of old watches you will need.

28 minutes ago, watchweasol said:

I still do it by hand,

Yey old timer, my hero 👍

1 hour ago, LuigiMeister2800 said:

Hi everyone,

 

I wondered what your suggestions would be for someone starting out in the hobby.
 

When you haven't got mainspring winders yet do you best:

  • Just leave it in the barrel and assemble everything after cleaning the rest
  • Take it out, measure it and buy a new one (don't know if that's feasible for older watches)
  • Take it out, measure it and get an appropriate mainspring winder
  • Something else....

Thanks for the advice!

In my eyes leaving it in the barrel isn't an option, when I started i thought about it and i tried it. I soniced the barrel upside down in the hope it would clean it, it did but not to an acceptable level at all. No way are between the coils gonna get clean or all of the bottom of the barrel. You have to bite the bullet and just get stuck in, have it out and hand wind it back in if there's no option of a winder. Practice ,practice and practice and when you're done practicing......... you've guessed it , practice some more.

  • Like 2
CYCLOPS WRT Addict

CYCLOPS

Posted
Posted

I think you should acquire some mainspring winders, you use/need them in the future, hand winding is a last resort for what ever reason, too much distortion especially from beginners, I think sometimes it is better to hand clean with arbor out and reassemble than hand wind, but I have winders so just my opinion.....new is a great option like Neverenough said...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • coreymsnow
      A lathe with indexing that won't break the bank?

      By coreymsnow · Posted

      Hi folks, I'm doing some homework on getting a watchmaker's lathe, and it's clear I have a lot to learn. But I know one goal: I want to be able to fabricate wheels, which would require an indexing capability. I know how to use large lathes- like, giant metal lathes- but my experience is a few decades old now (but you never forget the smell of the metal cutting oil). So I'm looking to learn anew, and have a goal to get to a point where I can fabricate some basic watch parts. I also have no specific timeframe and want to do this right, so I'll be patient and learn what I need to before spending the money. I know I'm not going to get anything for a pittance, but I'm also not really able to put together the scratch for a $5-$10k lathe. What's out there for a hobbyist that can either handle some fabrication out of the box or can be relatively easily made to do so? Thanks!  
    • Nucejoe
      Good afternoon from Marbella, Spain

      By Nucejoe · Posted

      Hello and welcome to the WRT forum.   This usually points to broken balance pivot.  Though a watch in need of clean & lube can do the same. Easiest diag would be to  see if balance pivot doesn't stay in hole jewel of the setting, when you lift one side of balance rim with an oiler or gently with pair of tweezers. Another would be to detach balance complete from the cock and take a look at pivot under high maginfication.  Regs 
    • MikeEll
      Help with Hermle ships clock

      By MikeEll · Posted

      Ahhh, yes.  I hadn’t thought of that.  I’ve serviced quite a few of these and the first time I didn’t realise it was a ships strike pattern!  Ha ha, confused me totally until I realised.
    • RichardHarris123
      Good afternoon from Marbella, Spain

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • Rixy
      Help with Hermle ships clock

      By Rixy · Posted

      Hi Mike, I did, thanks. Found this clip that was really helpful:   It says Seth Thomas but it's actually the same Hermle I've been working on. I'd had it working correctly all along but hadn't noticed that the lever with the sprung end stops the hammer a bit short of the bell on the second ding at the end of the half-past sequence. If only I'd put the bell on when testing, rather than just looking at the hammer, my ears would have told me it was working,  even if my eyes didn't!  
×
×
  • Create New...