Jump to content

L&R Ultrasonic Solutions

MarkF
 Share

Recommended Posts

MarkF Member

MarkF

Posted
Posted

Just bought and am about to try the L&R ultrasonic cleaner and rinse in my ultrasonic machine. A few quick questions:

1). I plan to seal the jars to reduce fumes. I don’t think that will be an issue (pressure buildup?) but curious if anyone has had an issue with this. 
 

2) I am planning a 4 minute wash followed by 2X 3 minute rinse. I am assuming it is not advisable to use heat with solvent based products, but again if anyone has advice in terms of an  optimal temperature - I’m all ears. 
 

3) If using a two jar solvent rinse process, is there any need for a third rinse in IPA or is that just overkill?

spectre6000 Distinguished Member

spectre6000

Posted
Posted

I keep mine in the jugs they came in and mason jars. I've not had any issues with it evaporating past the seals. One Dip is the only watch cleaning chemical I've experienced that with.

I usually do fives, but it's pretty arbitrary. However long it takes to get the job done without doing damage is fine. I usually turn the heater on when I start, but don't really wait for it to get there. I've done it cold as well, and haven't noticed any difference. 

Rinsing in IPA is probably not as good as the L&R rinse. I doubt it's undoing any of the cleaning progress made, but it's not really gaining you anything either.

  • Like 3

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • coreymsnow
      A lathe with indexing that won't break the bank?

      By coreymsnow · Posted

      Hi folks, I'm doing some homework on getting a watchmaker's lathe, and it's clear I have a lot to learn. But I know one goal: I want to be able to fabricate wheels, which would require an indexing capability. I know how to use large lathes- like, giant metal lathes- but my experience is a few decades old now (but you never forget the smell of the metal cutting oil). So I'm looking to learn anew, and have a goal to get to a point where I can fabricate some basic watch parts. I also have no specific timeframe and want to do this right, so I'll be patient and learn what I need to before spending the money. I know I'm not going to get anything for a pittance, but I'm also not really able to put together the scratch for a $5-$10k lathe. What's out there for a hobbyist that can either handle some fabrication out of the box or can be relatively easily made to do so? Thanks!  
    • Nucejoe
      Good afternoon from Marbella, Spain

      By Nucejoe · Posted

      Hello and welcome to the WRT forum.   This usually points to broken balance pivot.  Though a watch in need of clean & lube can do the same. Easiest diag would be to  see if balance pivot doesn't stay in hole jewel of the setting, when you lift one side of balance rim with an oiler or gently with pair of tweezers. Another would be to detach balance complete from the cock and take a look at pivot under high maginfication.  Regs 
    • MikeEll
      Help with Hermle ships clock

      By MikeEll · Posted

      Ahhh, yes.  I hadn’t thought of that.  I’ve serviced quite a few of these and the first time I didn’t realise it was a ships strike pattern!  Ha ha, confused me totally until I realised.
    • RichardHarris123
      Good afternoon from Marbella, Spain

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • Rixy
      Help with Hermle ships clock

      By Rixy · Posted

      Hi Mike, I did, thanks. Found this clip that was really helpful:   It says Seth Thomas but it's actually the same Hermle I've been working on. I'd had it working correctly all along but hadn't noticed that the lever with the sprung end stops the hammer a bit short of the bell on the second ding at the end of the half-past sequence. If only I'd put the bell on when testing, rather than just looking at the hammer, my ears would have told me it was working,  even if my eyes didn't!  
×
×
  • Create New...