Jump to content

ETA 2790 setting time problem

Hiaz224
 Share

Recommended Posts

Hiaz224 Member

Hiaz224

Posted
Posted

Hello!

This is my 3rd post and this time I would need help to go on with my project, so thanks in advance:

The 2790 is already serviced with a reasonable performance using. when I was fixing the hands to case the movement I noticed that setting the time required high torque to move the hands. The time-grapher showed about the same performance...

I double checked and noticed that when I take out the pallet fork  the time setting is back to normal (soft). I can't understand the relation between the pallet fork and the time setting... 

Additional info:

1. I double checked the calendar mechanism

2. Double checked the remontoir mechanism

3. I can't manually move the wheels when the pallet fork is installed and the balance is out of the movement.

So, it seems that I am doing something wrong and the only thing I notice is that if the balance is installed the watch works but the time setting is too hard. If the pallet fork is not installed I can set the time without a problem... I put back the pallet fork and it ticks when is touched but the hands are again hard to move.

Please let me know if you need any other information. 

Thanks for reading my post.

Fernando

 

eccentric59 WRT Addict

eccentric59

Posted
Posted

Just to be clear, when the watch is assembled and the setting position is stiff, the hands still move, correct?

By removing the pallet fork you allow the train to run freely, so when you put the keyless works in the setting position, the cannon pinion won't slide and  you are turning both the motion works and the train. The 2970 uses a cannon pinion wheel setup like this image.thumb.png.41b328dd4a81378d74b663c5380919da.png

Make sure you've lubricated the contact points between the wheel and pinion.

  • Like 2
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi Fernando,   When the patter fork is installed you cannot move the train  as it’s locked by the pallet. And it yo7 can’t move the train with ths pallet fork a balance you have a problem. With the train installed and a couple of turn# on the mainspring the train should move freely. Ok can only suggest dismantling the watch and reassembling it again checking each stage as you complete it 

start with mainspring and train wheels, always checking the train freedom.  When assembling the keyless work make sure the right screws are in the right places.   If you look on cousins uk web site and look in document down loads you 2ill be able to find and print the technical sheet for this movement eta 2790.

Hiaz224 Member

Hiaz224

Posted
  • Author
Posted
53 minutes ago, watchweasol said:

Hi Fernando,   When the patter fork is installed you cannot move the train  as it’s locked by the pallet. And it yo7 can’t move the train with ths pallet fork a balance you have a problem. With the train installed and a couple of turn# on the mainspring the train should move freely. Ok can only suggest dismantling the watch and reassembling it again checking each stage as you complete it 

start with mainspring and train wheels, always checking the train freedom.  When assembling the keyless work make sure the right screws are in the right places.   If you look on cousins uk web site and look in document down loads you 2ill be able to find and print the technical sheet for this movement eta 2790.

Hi! My bad. I meant to say that when the pallet fork is installed I cant move the wheels "using the crown in the setting position" Really in truly my number 3 was redundant and badly written (trying to explain myself went all wrong).

I dismantling partially the watch (calendar, remontoir, Balance and Pallet fork). I think I would need to go that way... 

Thanks for your comments...

 

1 hour ago, eccentric59 said:

Just to be clear, when the watch is assembled and the setting position is stiff, the hands still move, correct? (Yes, but slowly and I need to apply high torque to the crown.)

By removing the pallet fork you allow the train to run freely, so when you put the keyless works in the setting position, the cannon pinion won't slide (this sentence is making me think as you can't imagine!!!) and  you are turning both the motion works and the train. The 2970 uses a cannon pinion wheel setup like this image.thumb.png.41b328dd4a81378d74b663c5380919da.png

Make sure you've lubricated the contact points between the wheel and pinion. Ups! I think here it is the root of my problem... (1. I did not oil where you mention!!!!!. 2. I took this setting and it seems or feels to me that the pinion does not rotate within the wheel and it should. )

This is my second ETA and I never stopped to think on how this setting works. I really appreciate your comments

Thanks Fernando

 

 

nevenbekriev Distinguished Member

nevenbekriev

Posted
Posted

Hi Fernando, read carefully what @eccentric59 wrote, it is the key to You problem. Lubricate the cannon pinion. Take care to understand what is it's function. When You set time, the train doesn't move, but only the cannon pinion moves. Put hte lever back in it's place, it has nothing to do with time setting

Hiaz224 Member

Hiaz224

Posted
  • Author
Posted

Yes. I understand (now). I regret to say that I am servicing watches without fulling understanding the cannon pinion function in relation with setting the time  (and many other theory aspects of the orology!!!). If is too tight the hands won't move and on the contrary. If the pallet fork is not installed the train of wheels will spin freely and if the remontoir is on the setting position the motion wheels will also move.

I will use HP 1300 for the cannon pinion setting.

I am happy and grateful and of course I will report back as soon as I can.

Thanks 

 

  • Like 1
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

Hi Hiaz,

I see you didn't get this link usually given to new members by oldhippy, here , useful stuff.

704789946_TZIllustratedGlossary(2).pdf
4.2 MB
 

  • Like 1
Hiaz224 Member

Hiaz224

Posted
  • Author
Posted

These are the places where I oiled with HP 1300... 

unnamed (1).jpg

unnamed.jpg

These are the places where I oiled with HP 1300... 

I can see that the cannon pinion is moving as it should once I installed the pallet fork. I created a small video but was not able to upload it. It is a mov file type.

I need now to source a GR4014X mainspring, a stop ever #9433 and both calendar disc as the days/dates are peeling out...

This is the mido watch which holds the ETA Movement....

I just want to thanks all of you guys for your help, specially @eccentric59 who nailed it!

So, I would consider this case as closed unless of course any question from any of you...

Best regards

Fernando

 

 

unnamed (2).jpg

8 hours ago, Nucejoe said:

Hi Hiaz,

I see you didn't get this link usually given to new members by oldhippy, here , useful stuff.

704789946_TZIllustratedGlossary(2).pdf
4.2 MB
 

I could not download the file... I will tray to located. Many thanks. 

Nucejoe Distinguished Member

Nucejoe

Posted
Posted
4 hours ago, Hiaz224 said:

 

unnamed (2).jpg

I could not download the file... I will tray to located. Many thanks. 

I just coppied this from a old post of  @oldhippy . 

Hang on , he'd be there in a sec.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • coreymsnow
      A lathe with indexing that won't break the bank?

      By coreymsnow · Posted

      Hi folks, I'm doing some homework on getting a watchmaker's lathe, and it's clear I have a lot to learn. But I know one goal: I want to be able to fabricate wheels, which would require an indexing capability. I know how to use large lathes- like, giant metal lathes- but my experience is a few decades old now (but you never forget the smell of the metal cutting oil). So I'm looking to learn anew, and have a goal to get to a point where I can fabricate some basic watch parts. I also have no specific timeframe and want to do this right, so I'll be patient and learn what I need to before spending the money. I know I'm not going to get anything for a pittance, but I'm also not really able to put together the scratch for a $5-$10k lathe. What's out there for a hobbyist that can either handle some fabrication out of the box or can be relatively easily made to do so? Thanks!  
    • Nucejoe
      Good afternoon from Marbella, Spain

      By Nucejoe · Posted

      Hello and welcome to the WRT forum.   This usually points to broken balance pivot.  Though a watch in need of clean & lube can do the same. Easiest diag would be to  see if balance pivot doesn't stay in hole jewel of the setting, when you lift one side of balance rim with an oiler or gently with pair of tweezers. Another would be to detach balance complete from the cock and take a look at pivot under high maginfication.  Regs 
    • MikeEll
      Help with Hermle ships clock

      By MikeEll · Posted

      Ahhh, yes.  I hadn’t thought of that.  I’ve serviced quite a few of these and the first time I didn’t realise it was a ships strike pattern!  Ha ha, confused me totally until I realised.
    • RichardHarris123
      Good afternoon from Marbella, Spain

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • Rixy
      Help with Hermle ships clock

      By Rixy · Posted

      Hi Mike, I did, thanks. Found this clip that was really helpful:   It says Seth Thomas but it's actually the same Hermle I've been working on. I'd had it working correctly all along but hadn't noticed that the lever with the sprung end stops the hammer a bit short of the bell on the second ding at the end of the half-past sequence. If only I'd put the bell on when testing, rather than just looking at the hammer, my ears would have told me it was working,  even if my eyes didn't!  
×
×
  • Create New...