Jump to content

No numbers on my broken Bulova movement. Any tips on how to determine correct replacement movement?

ChefTofi
 Share

Recommended Posts

ChefTofi New Member

ChefTofi

Posted
Posted

Hello

I have 2007 Bulova watch with a damaged movement that I want to replace.  Not a particularly valuable watch, but it was a gift from my wife and has sentimental value.  There are no visible numbers on the movement (except in the battery well, 280-34).  My best guess is that I have a Miyota movement, but I don't know if any of the items currently shown at the Miyota site are appropriate replacements.  The watch repair service I contacted for an estimate wants me to specify which movement I need (I was hoping they could do that for me).  I have been searching the web for an answer, but no luck.  The Miyota site provides spec sheets and engineering drawings with measurements, but I don't have the tools or expertise to measure my watch to the required level of precision in order to determine fit.

Can any of you nice folks offer advice on how to determine the movement model that was originally installed in my watch?  I am hoping there is an information base somewhere that I have not yet been able to discover.

Thank you.

 

Bulova.JPG.d1ef1b70ed33bdc43f8566595ac04bb8.JPG

 

Link to comment
Share on other sites
  • 2 weeks later...
rossjackson01 Super WRT Addict

rossjackson01

Posted
Posted (edited)
2 minutes ago, ChefTofi said:

Thank you, Randy.  I have indeed learned that it's a Miyota movement (6M55) which is no longer available.  Ali Baba sells a purported generic equivalent for $8 with additional $8 shipping from China.  I will give that a try.

Let us know how you got on. Updates are good.

Edited by rossjackson01
Link to comment
Share on other sites
ChefTofi New Member

ChefTofi

Posted
  • Author
Posted
On 3/9/2024 at 9:55 AM, rossjackson01 said:

Let us know how you got on. Updates are good.

Ali Baba's movement fits and works - I managed to successfully disassemble and reassemble the watch (thanks to some youtube tutorials).  The date numerals are oriented sideways (90 degrees rotated from the correct orientation) on the replacement movement, but I can ignore that.  They were almost impossible to see anyway, so that "feature" doesn't really affect the appearance.  I was afraid I might mangle the hands or damage the dial face, but I managed to avoid that.  

Thanks for your replies, everyone.  I don't know if I'll end up fixing any  more quartz watches, but it's nice to know I probably can if I need to.

Peace to you all.

 

 

 

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • luiazazrambo
      WWW Eterna sucked me in.

      By luiazazrambo · Posted

      HWGIKE#57 Valex FEF 190 15 jewels Swiss lever full service and repair This one was waiting for a balance staff replacement in my cabinet parts and case cleaned up with a new balance staff and a 4th wheel as the original 4th wheel had a broken pivot for the off center second hand. I never attempted a balance staff replacement before however I received a Bergeon Molfres (i was hunting it for about 2 years) and with the help of it I managed to remove the old staff and riveted the new one in. It also received a new MS, crystal and the hole for the MS arbor was also tightened. With the new MS now it has an acceptable performance meaning that the amplitude goes up to 280 fully wound, has an acceptable beat error and I have the two nice lines but only dial up, dial down is not as nice and I could not figure out as why. I have the two lines but the amplitude is dropping to around 230 and the lines are a bit hairy. Both dial up and dial down the lines just go up and down without seemingly any pattern. I cleaned the movement two times, and then a 3rd time pegged out the main plate and train bridge holes but made no change. Both the HS collet and the roller table was too lose on the new staff... I did not count how many times I took the balance cock off to sort out the HS collet, the roller table and the beat error, somebody before me also shortened the HS by pushing it out a bit and it seems every time somebody is messing with the end of the HS the protruding bit is most of the time twisted bent etc. This one was probably one of the most challenging repair and service. I might take the new MS out and clean it lubricate it as I just pushed the new one in to the barrel from the retaining ring. Plus started to re-read the theory of the escapement and how to analyse the graph on the timing machine: Greiner Chronografic Record manual. I am also thinking to put the watch on a 24 hour long run with the eTimer SW it once helped me to figure out what was wrong with a watch. There is an interesting part of the Greiner record manual talking about the pallets and the end shake of the balance and pallet staff. Maybe this is my issue? Who could that possibly identify? After a few years now I am still without a clue how could watchmakers make parts I can only see with my microscope or how could/can they carry out complicated services impossible to do.. real magic..... .... ..... before I sent this post while the pics were uploading I had an idea, i was browsing the possible outcomes on the timing machine I had one for magnetism..... so I demagnetized the movement and it is not hairy now.... two really nice lines 0.2 ms beat error still a bit wavy, but a lot lot better..... argh....  
    • Nucejoe
      Hello from Cypress, CA

      By Nucejoe · Posted

      Hi there, welcome here.  
    • JohnR725
      No images showing

      By JohnR725 · Posted

      yes the advertising revenue should generate money. The question is how much money? Then as far as the cost of the website goes that's relatively easy to determine? all you would have to do to grasp costs and profitability would be to go to the link below and you can actually get a website for free try it out for free I believe you get no advertising initially. They also talk about that they'll help you out they have marketing tools and some sort of paid subscription or something. So I guess were shopping for a whatever just ask them what would a maybe could use this one as an example in other words it's going to look basically identical to this is going to have advertising a paid subscriptions what's it going to cost? After all they want to sell or give us a message board like this they should bill answer the questions as they're the people who did the software for this. Yes they really said you can have a free discussion group at least to start. https://invisioncommunity.com/ I was curious about the monthly supporter thing where exactly do we find that on this message board? A quick search I'm not finding it so obviously I'm not looking in the right place?
    • Curare
      No images showing

      By Curare · Posted

      Help me out here, but with all the advertising on this site (which I don't mind) wouldn't it pay for itself or even make money for the owner ???
    • Geri
      Seiko Twin Quartz 9983 Auxillary Oscillator tuning

      By Geri · Posted

      Wie ging die Sache weiter?   please use English for your posts    Tom
×
×
  • Create New...