Jump to content

Movement identification

martin1976
 Share

Recommended Posts

martin1976 New Member

martin1976

Posted
Posted

Hello guys, I'm trying to identify a movement for my friend from an unknown brand of the following pocket watch

Screenshot_20240322_205521_Messages.thumb.jpg.f2165abc9ce1b24f74e674126a27545f.jpg

the movement have the balance broken and me and my friend would love to bring that old guy back to life because this watch belonged to his grand dad and he would love to keep some memories for him

here is the movement we would like to identify 

Screenshot_20240322_205107_Messages.thumb.jpg.8d96b2758216ff4d6640e397e440ac3d.jpg

If you could please help in any way with the identity of this movement, it would be very nice and you would contribute to the repair of one of the many exceptional watches that have a really rich history and it would be a shame to let them gather dust. If by some miracle you could also advise us where to buy a balance or donor movement if the parts for it are no longer available anywhere, that would be lovely bonus for my friend

Thanks in advance for reading and sharing your valuable experience and/or advices 

Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
12 hours ago, martin1976 said:

I appreciate the quick replies, I'll try to solve it with a friend that we will have the missing piston made somewhere, because basically the rest of the balance is preserved

 

13 hours ago, martin1976 said:

I appreciate the quick replies, I'll try to solve it with a friend that we will have the missing piston made somewhere, because basically the rest of the balance is preserved

Add a picture of the balance parts so they can be assessed.  Dont assume that everything else will be ok, its very likely it wont be. Take it step by step with help from here.

  • Like 2
  • Thanks 1
Link to comment
Share on other sites
martin1976 New Member

martin1976

Posted
  • Author
Posted
8 hours ago, Neverenoughwatches said:

 

Add a picture of the balance parts so they can be assessed.  Dont assume that everything else will be ok, its very likely it wont be. Take it step by step with help from here.

 

5 hours ago, oldhippy said:

Making a cylinder is extremely difficult, they are so hard it is like glass. They consist of three parts, the center and a plug each end which has the points. Here is a picture so you can see what I mean.

  

Cylinder three parts.jpg

 

3 hours ago, Nucejoe said:

 I have seen tons of  these types of parts( used)  in my late watchmaker's stuff, unidentified , guess he knew them just by looking. 

Need full measurements to look for what you need.

Rgds

 

2 hours ago, oldhippy said:

There are countless movements of this type about, but they are not universal and it is highly unlikely that parts from a movement will fit others. 

I appreciate the quick replies, I'll try to solve it with a friend that we will have the missing piston made somewhere, because basically the rest of the balance is preserved

 

Thanks again guys I do appreciate your effort, the watch isn't in my position so I can't take the measurements, its with the aforementioned friend, I recommended him to buy the exact same watch for spare parts, but I don't know what he will decide to do, I just tried to help him as much as I could

Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
17 hours ago, martin1976 said:

 

 

 

I appreciate the quick replies, I'll try to solve it with a friend that we will have the missing piston made somewhere, because basically the rest of the balance is preserved

 

Thanks again guys I do appreciate your effort, the watch isn't in my position so I can't take the measurements, its with the aforementioned friend, I recommended him to buy the exact same watch for spare parts, but I don't know what he will decide to do, I just tried to help him as much as I could

The watch may not be identifiable, even if so watches of this age still vary made by the same maker. Balance parts need to be assessed , if one of the cyljnder plugs are damaged then this part should be easy for a watchmaker to source or make. It is also something he would need to fit and adjust to the watch, not something a something a hobbyist with limited experience should tackle. I tried this myself a few months ago only to fail miserably breaking the cylinder in half, believe it or not i consider i was being very careful 😂

  • Like 1
  • Thanks 1
Link to comment
Share on other sites
praezis Distinguished Member

praezis

Posted
Posted

In this case usually a replacement cylinder is installed. There are still many NOS PW cylinders around. 

As correctly mentioned, a watchmaker’s task. Different sizes must be regarded,  exact diameter and length being basic but far from sufficient.

Frank

  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ChrisInOz
      No images showing

      By ChrisInOz · Posted

      The post below contains the link. If you don't already have a discord account it will take you to the registration screen.  Registration is free.   https://www.watchrepairtalk.com/topic/31653-mark/?do=findComment&comment=279066
    • luiazazrambo
      WWW Eterna sucked me in.

      By luiazazrambo · Posted

      HWGIKE#57 Valex FEF 190 15 jewels Swiss lever full service and repair This one was waiting for a balance staff replacement in my cabinet parts and case cleaned up with a new balance staff and a 4th wheel as the original 4th wheel had a broken pivot for the off center second hand. I never attempted a balance staff replacement before however I received a Bergeon Molfres (i was hunting it for about 2 years) and with the help of it I managed to remove the old staff and riveted the new one in. It also received a new MS, crystal and the hole for the MS arbor was also tightened. With the new MS now it has an acceptable performance meaning that the amplitude goes up to 280 fully wound, has an acceptable beat error and I have the two nice lines but only dial up, dial down is not as nice and I could not figure out as why. I have the two lines but the amplitude is dropping to around 230 and the lines are a bit hairy. Both dial up and dial down the lines just go up and down without seemingly any pattern. I cleaned the movement two times, and then a 3rd time pegged out the main plate and train bridge holes but made no change. Both the HS collet and the roller table was too lose on the new staff... I did not count how many times I took the balance cock off to sort out the HS collet, the roller table and the beat error, somebody before me also shortened the HS by pushing it out a bit and it seems every time somebody is messing with the end of the HS the protruding bit is most of the time twisted bent etc. This one was probably one of the most challenging repair and service. I might take the new MS out and clean it lubricate it as I just pushed the new one in to the barrel from the retaining ring. Plus started to re-read the theory of the escapement and how to analyse the graph on the timing machine: Greiner Chronografic Record manual. I am also thinking to put the watch on a 24 hour long run with the eTimer SW it once helped me to figure out what was wrong with a watch. There is an interesting part of the Greiner record manual talking about the pallets and the end shake of the balance and pallet staff. Maybe this is my issue? Who could that possibly identify? After a few years now I am still without a clue how could watchmakers make parts I can only see with my microscope or how could/can they carry out complicated services impossible to do.. real magic..... .... ..... before I sent this post while the pics were uploading I had an idea, i was browsing the possible outcomes on the timing machine I had one for magnetism..... so I demagnetized the movement and it is not hairy now.... two really nice lines 0.2 ms beat error still a bit wavy, but a lot lot better..... argh....  
    • Nucejoe
      Hello from Cypress, CA

      By Nucejoe · Posted

      Hi there, welcome here.  
    • JohnR725
      No images showing

      By JohnR725 · Posted

      yes the advertising revenue should generate money. The question is how much money? Then as far as the cost of the website goes that's relatively easy to determine? all you would have to do to grasp costs and profitability would be to go to the link below and you can actually get a website for free try it out for free I believe you get no advertising initially. They also talk about that they'll help you out they have marketing tools and some sort of paid subscription or something. So I guess were shopping for a whatever just ask them what would a maybe could use this one as an example in other words it's going to look basically identical to this is going to have advertising a paid subscriptions what's it going to cost? After all they want to sell or give us a message board like this they should bill answer the questions as they're the people who did the software for this. Yes they really said you can have a free discussion group at least to start. https://invisioncommunity.com/ I was curious about the monthly supporter thing where exactly do we find that on this message board? A quick search I'm not finding it so obviously I'm not looking in the right place?
    • Curare
      No images showing

      By Curare · Posted

      Help me out here, but with all the advertising on this site (which I don't mind) wouldn't it pay for itself or even make money for the owner ???
×
×
  • Create New...