Jump to content

Fusee chain

Michael1962

By Michael1962
in All Things Clocks

 Share

Recommended Posts

Michael1962 Distinguished Member

Michael1962

Posted
Posted

Firstly, no I do not have one. 
Secondly, I have just been thinking how you would go about making a chain from scratch?

For a clock (which is why I put this question in here) it would be easier based on size, but it would still be a tough job and quite an achievement. 
For a pocket watch? I am quite baffled to put it simply. 
So are there any takers on here that can explain to me how it is done?

Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted (edited)
13 minutes ago, RichardHarris123 said:

I'm baffled too, they were made with basic tools, by children I think.  

👍 small children have the better eyesight, smaller more nibble fingers. I expect l might be quite good at it considering i can be childlike, shame about the big hands and dodgy eyesight though.

Edited by Neverenoughwatches
Link to comment
Share on other sites
RichardHarris123 Distinguished Member

RichardHarris123

Posted
Posted
4 minutes ago, Neverenoughwatches said:

expect l might be quite good at it considering i can be childlike, shame about the big hands and dodgy eyesight though.

Plus you're a rough a%£e joiner, who only needs to be within 4mm, decorators calk will fill the gap. Hehe. 

Watch this 

https://youtu.be/os3Vthd_Us4?si=43Bc8ItUh4Z4zh7N

 

 

  • Like 2
  • Haha 1
Link to comment
Share on other sites
nevenbekriev Distinguished Member

nevenbekriev

Posted
Posted (edited)

What I know is that chains were only assembled by MYOPIC children. Their sights degraded for several years and thus they had short and unhappy lifes. The children were bought by the watchmakers from their parrents...

Edited by nevenbekriev
Link to comment
Share on other sites
tomh207 Distinguished Member

tomh207

Posted
Posted
10 minutes ago, nevenbekriev said:

What I know is that chains were only assembled by MYOPIC children. Their sights degraded for several years and thus they had short and unhappy lifes. The children were bought by the watchmakers from their parrents...

That is such a so very sad thing to hear and realise nev. all the horrors that have been inflicted on people,especially young people, in past centuries should give us pause to think how our children are being manipulated today for profit albeit in a different way.

 

Tom

  • Like 2
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted
17 hours ago, RichardHarris123 said:

I'm baffled too, they were made with basic tools, by children I think.  

That is correct, also in poor light don't forget back the children worked long hours. It is hard enough to repair one.  If you have a clock and the chain has broken and providing it's value is not high it is best to adapt it so it takes a line which involves a bit of work and working out. 

  • Like 1
Link to comment
Share on other sites
Michael1962 Distinguished Member

Michael1962

Posted
  • Author
Posted

Was the chain built with two side plates to each link like a motorcycle chain, or was every other link just a single plate with the next link having two plates?

I presume the links were only about 3mm long in a pocket watch? A bit bigger in a clock.

Still amazing though.

Link to comment
Share on other sites
  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ChrisInOz
      No images showing

      By ChrisInOz · Posted

      The post below contains the link. If you don't already have a discord account it will take you to the registration screen.  Registration is free.   https://www.watchrepairtalk.com/topic/31653-mark/?do=findComment&comment=279066
    • luiazazrambo
      WWW Eterna sucked me in.

      By luiazazrambo · Posted

      HWGIKE#57 Valex FEF 190 15 jewels Swiss lever full service and repair This one was waiting for a balance staff replacement in my cabinet parts and case cleaned up with a new balance staff and a 4th wheel as the original 4th wheel had a broken pivot for the off center second hand. I never attempted a balance staff replacement before however I received a Bergeon Molfres (i was hunting it for about 2 years) and with the help of it I managed to remove the old staff and riveted the new one in. It also received a new MS, crystal and the hole for the MS arbor was also tightened. With the new MS now it has an acceptable performance meaning that the amplitude goes up to 280 fully wound, has an acceptable beat error and I have the two nice lines but only dial up, dial down is not as nice and I could not figure out as why. I have the two lines but the amplitude is dropping to around 230 and the lines are a bit hairy. Both dial up and dial down the lines just go up and down without seemingly any pattern. I cleaned the movement two times, and then a 3rd time pegged out the main plate and train bridge holes but made no change. Both the HS collet and the roller table was too lose on the new staff... I did not count how many times I took the balance cock off to sort out the HS collet, the roller table and the beat error, somebody before me also shortened the HS by pushing it out a bit and it seems every time somebody is messing with the end of the HS the protruding bit is most of the time twisted bent etc. This one was probably one of the most challenging repair and service. I might take the new MS out and clean it lubricate it as I just pushed the new one in to the barrel from the retaining ring. Plus started to re-read the theory of the escapement and how to analyse the graph on the timing machine: Greiner Chronografic Record manual. I am also thinking to put the watch on a 24 hour long run with the eTimer SW it once helped me to figure out what was wrong with a watch. There is an interesting part of the Greiner record manual talking about the pallets and the end shake of the balance and pallet staff. Maybe this is my issue? Who could that possibly identify? After a few years now I am still without a clue how could watchmakers make parts I can only see with my microscope or how could/can they carry out complicated services impossible to do.. real magic..... .... ..... before I sent this post while the pics were uploading I had an idea, i was browsing the possible outcomes on the timing machine I had one for magnetism..... so I demagnetized the movement and it is not hairy now.... two really nice lines 0.2 ms beat error still a bit wavy, but a lot lot better..... argh....  
    • Nucejoe
      Hello from Cypress, CA

      By Nucejoe · Posted

      Hi there, welcome here.  
    • JohnR725
      No images showing

      By JohnR725 · Posted

      yes the advertising revenue should generate money. The question is how much money? Then as far as the cost of the website goes that's relatively easy to determine? all you would have to do to grasp costs and profitability would be to go to the link below and you can actually get a website for free try it out for free I believe you get no advertising initially. They also talk about that they'll help you out they have marketing tools and some sort of paid subscription or something. So I guess were shopping for a whatever just ask them what would a maybe could use this one as an example in other words it's going to look basically identical to this is going to have advertising a paid subscriptions what's it going to cost? After all they want to sell or give us a message board like this they should bill answer the questions as they're the people who did the software for this. Yes they really said you can have a free discussion group at least to start. https://invisioncommunity.com/ I was curious about the monthly supporter thing where exactly do we find that on this message board? A quick search I'm not finding it so obviously I'm not looking in the right place?
    • Curare
      No images showing

      By Curare · Posted

      Help me out here, but with all the advertising on this site (which I don't mind) wouldn't it pay for itself or even make money for the owner ???
×
×
  • Create New...