Jump to content

Solid collet loose on Omega 625 - best fix?

mikepilk
 Share

Recommended Posts

mikepilk Distinguished Member

mikepilk

Posted
Posted (edited)

I had to put a new balance staff in an Omega 625. I did a visual check before fitting, and it looked the same as the old staff.

It rivetted in as expected, and the roller fitted well, but then I found that the hairspring collet is very loose. 

The balance staff was sold as genuine Omega NOS from a trader I've used before. I have another staff from another trader, also sold as Omega NOS. The collet is equally loose on that one too. Both staffs look to be the quality you would expect from Omega.

It's a solid collet, so I cannot do the usual fix of closing the slot.

What's the best option. Try to close the holes - I'm not sure I have a stake with such a finely curved tip.  Shellac, Loctite ?

 

WIN_20240711_09_16_49_Pro.thumb.jpg.51046813188ccc9d6932b18c09ff701c.jpg

Edited by mikepilk
typo
mikepilk Distinguished Member

mikepilk

Posted
  • Author
Posted
14 minutes ago, SwissSeiko said:

easiest would be locktite on an oiler. proper way is probably shellac, but thats a tough place to work in with how quickly shellac hardens.

It's so loose it rocks slightly. So I'd like to use shellac, but this is a small balance (hairspring only 3.5mm dia), and there's danger of getting shellac on the hairspring 😟

The smallest hole closing pusher in my jewelling tool looks like it should work. I'm tempted to try that to close the hole, then use Loctite.

SwissSeiko WRT Addict

SwissSeiko

Posted
Posted (edited)
6 minutes ago, mikepilk said:

It's so loose it rocks slightly. So I'd like to use shellac, but this is a small balance (hairspring only 3.5mm dia), and there's danger of getting shellac on the hairspring 😟

The smallest hole closing pusher in my jewelling tool looks like it should work. I'm tempted to try that to close the hole, then use Loctite.

do you have flake or stick shellac? If you have flake, you could put the smallest little flake at the base of the collet, then heat it up similar to a pallet warmer. Or maybe you could drop a flake in through the top opening and do the same thing? I can believe it isn't slotted. That's so strange.

Edited by SwissSeiko
  • Like 1
mikepilk Distinguished Member

mikepilk

Posted
  • Author
Posted (edited)
7 minutes ago, SwissSeiko said:

do you have flake or stick shellac? If you have flake, you could put the smallest little flake at the base of the collet, then heat it up similar to a pallet warmer. I can believe it isn't slotted. That's so strange.

I have flaked shellac. I might try that. I have an old pocket watch mainplate I use. It has enough mass to keep hot for a while so I can work under the microscope. The pivot holes are useful for sitting parts in.

(BTW the movement has an adjustable stud holder, so I don't need to worry about aligning the collet)

Edited by mikepilk
SwissSeiko WRT Addict

SwissSeiko

Posted
Posted
3 minutes ago, mikepilk said:

I have flaked shellac. I might try that. I have an old pocket watch mainplate I use. It has enough mass to keep hot for a while so I can work under the microscope. The pivot holes are useful for sitting parts in.

(BTW the movement has an adjustable stud holder, so I don't need to worry about aligning the collet)

That's a good idea using the main plates! As far as alignment with the collet, you do need to be able to line up the roller jewel within the banking pins, so I would make sure that is in alignment, mark where the stud is on the radius of the balance wheel, and then you can cement it with the shellac. Its a lot easier to align is this way then to try and adjust the roller table since its pressed on quite tight.

mikepilk Distinguished Member

mikepilk

Posted
  • Author
Posted

I marked on the balance rim the positions of the roller jewel and stud before disassembly. As the stud holder is adjustable, I can adjust beat error, so don't need to be precise with positions.

I've just thought of a problem. With the roller fitted, the jewel might fall out when I heat the balance. But if I remove the roller to shellac the collet, it won't be easy to refit with the hairspring on.

SwissSeiko WRT Addict

SwissSeiko

Posted
Posted
24 minutes ago, mikepilk said:

I marked on the balance rim the positions of the roller jewel and stud before disassembly. As the stud holder is adjustable, I can adjust beat error, so don't need to be precise with positions.

I've just thought of a problem. With the roller fitted, the jewel might fall out when I heat the balance. But if I remove the roller to shellac the collet, it won't be easy to refit with the hairspring on.

That is true. In that case, could you put the shellac here and heat it from above with a torch?

 

image.png.21cc4246060d1001cb237afd4134fd20.png

mikepilk Distinguished Member

mikepilk

Posted
  • Author
Posted
1 hour ago, RichardHarris123 said:

I would try a modern adhesive, I  have now barricaded the doors and windows awaiting the men with pitchforks.  

(Puts on tin hat) I have UV activated resin. That should work well.  and I believe it can be dissolved in IPA or acetone if necessary.

Nucejoe Distinguished Member

Nucejoe

Posted
Posted

 Not just the hairpsring , but the pivot must be cleanest with no adhesive on it.

1- I smear a bit of shellac on  base of the pivot,

2-Let dry,

3-Shave off ( with safety razor blade) any shellac that's not where its suppose to be. in case any adhesive  has got on pivot,  clean entirely  and try again.

4- Press the collet onto the pivot, make sure no shellac has got  on the wrong part,

5- Apply heat ( soldering gun) to the collet, until shellac re-melts, the melted shellac fills all available cavities. 

You can also steal nail polish from the lady and follow the same procedure except no need for heat. Nail polish does not damage metals.  

  • Thanks 1
mikepilk Distinguished Member

mikepilk

Posted
  • Author
Posted (edited)

I only have shellac flakes, so I'll have to dissolve some.  Then using the soldering iron sounds a safe way. 

EDIT

I've just discovered why the new collet is so loose on both new staffs. The old staff measures 0.45mm diameter at the collet. The spec is 0.42mm

 

Edited by mikepilk
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

 I am not sure if heat deforms pivots when doing this, so I try to carefully apply heat to the collet only. 

 Nail polish is the safest I know of, have not seen any sign of chemical damage to the metal by nail polish applied 50 years ago.

 

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • BobG
      Etachron regulation system

      By BobG · Posted

      I’ve been playing with a NH35 movement that which has the classic Etachron regulation system and a few balance assemblies as practice. What I’m trying to do is get comfortable with the effect both the stud and regulator pin positions have on rate and positional error. When I install a new balance assembly I install it with the assembly in place  on the cock and cock is attached to base plate. I use the back of the tweezers to push the stud into place and feel the click. However, I noticed that the angle of the stud can be adjusted and what I also noticed is that some movements have the stud carrier arm bent down a little and that changes the angle of the hairspring leaving the stud. This angle effects how the spring goes through the regulator pins and also the spacing of the coils opposite the stud. What I thought I was supposed to do is set the regulator block in the middle of the curve, open the pins, and use the stud angle to center the spring.  Then the stud is set.  Now on all the new NH movements I have seen the angle of the regulator block is about 60 degrees counter clockwise from full open. I watched a video where the author used the regulator pin adjust to adjust rate and position error. When I close down the pins I do notice that the rate increases but also the amplitude drops, the coil spacing changes and hairspring appears slight straighter between the stud and the regulator block. If I open the pins the amplitude comes back, the spring breathes a bit more between the stud and the regulator block and the rate slows.  So, a long post I know but I would really appreciate any advice on how to correctly adjust the etachron system for rate, amplitude and positional error.   
    • Neverenoughwatches
      New forum member, new learner

      By Neverenoughwatches · Posted

      Aw come on Andy, it was just a comparison between spending 30 quid and tackling a tricky piece of work. You appeared to be volunteering,  i volunteer for stuff all the time it gets me into all kinds of trouble.
    • Neverenoughwatches
      Tissot case back removal

      By Neverenoughwatches · Posted

      It's not really shown here , but the blade flips over, so it faces the other way. The knob and threaded case holder then pushes the caseback seam into the blade. Once the blade starts to penetrate into it, the lever and blade are lifted , which should hopefully pop the back off. A lot of fashion style cases have very tight seams and need a sharp blade to start separating them.  Don't buy the cheaper plastic versions of this tool, the posts with the pins through for blade holder break easily if the apply extra force to blade. 
    • tomh207
      New forum member, new learner

      By tomh207 · Posted

      You will still be looking for a balance complete I’m afraid, this is the balance staff, balance wheel and hairspring in one package. Hairspring and the balance wheel are matched in the factory. Whilst we can change a balance staff the hairspring and balance wheel stay together.   Tom
    • chrisG
      New forum member, new learner

      By chrisG · Posted

      The hairspring end has come adrift from the small terminal barrel.  I have tried to remove the taper pin to relocate it, but the task is beyond my skill set, eyes, hands and being in my 70s, probably beyond my life expectancy.  It is not too badly mangled on the end.  On the ebay offer, that really is a bit on the rich side.  I'll keep looking, maybe a good hairspring will turn up with a shot balance staff. As for time spent on knees.  I made up one of these from 3M magnetic tape and a piece of wood.  It works well for magnetic parts. Other things I have suffered with.  I found lubricants so very expensive that I bought some very small syringes and tiny needles.  I just decant a drop into my oiling pots when I start a movement and the remainder keeps really well in the syringes. Finally identifying the correct screw for the part led me to make up the board in the final pic.   Thanks for the info. Kind regards   Chris  
×
×
  • Create New...