Jump to content

Slipping Anchor pallet

dnhb

By dnhb
in All Things Clocks

 Share

Recommended Posts

dnhb WRT Addict

dnhb

Posted
Posted

Working on a friend's Bracket clock (Westminster chime) I noted it needed a rather extreme tilt to get in beat. Adjusted the crutch to reduce this & clock ran to time for a day or two but then stopped. On attempting restart it's clear the Anchor pallet has slipped/rotated laterly on its arbour. This one, unlike the other I've fixed, doesn't have a screw with which to secure it on the arbour. Are there any other fixes other than drilling & tapping this one?

dnhb WRT Addict

dnhb

Posted
  • Author
Posted
On 8/6/2024 at 7:02 PM, oldhippy said:

I need to see the pallets and arbor. 

Thanks for your interest, OH. Hope the attached helps you formulate some advice...

20240808_165859.jpg

oldhippy Distinguished Member

oldhippy

Posted
Posted (edited)

As I feared the complete pallets are pushed/ hammered onto a tapered rod. You will have to take the complete unit off before you mark where the should go. You need to close the hole by using a stake punch around the hole so it is a tight friction fit. You could also use some locktight, blue is strong but easy to move red is stronger and more permanent.     

The movement is Gustav becker which is German. 

Edited by oldhippy
  • Thanks 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • transporter
      Smiths rim wind and set

      By transporter · Posted

      Ok, as per pictures I have a smiths rim set and wind on the bench, swimming in oil but all sorted. The fault I have is the mainspring bridle has lost its tab/notch/hook, like a hebdomas pocket watch the mainspring is fitted to a bridal in the barrel which slides around on full wind onto 4 notches in the barrel wall, thus stopping damage to the mainspring by over enthusiastic winding. So my questiion is this, what is the best way to create another hook in the bridal, my thoughts are along the same lines as making a new hole in the mainspring end, annealing etc, but what and how to make the hook?? I have a pair of barrel hook pliers that work great in soft brass but won’t even scratch the bridal, what I don’t want to do is whack a hole into it and not have a hook. the pictures are of the bridal ( broken) and a hebdomas ( complete ) incase you are wondering what I’m on about. And a few of the serivce. Thanks for any advise.
    • zx6rfool
      Replacing, upgrading Ronda 715 Harley?

      By zx6rfool · Posted

      Decided to give the case and bracelet a good cleaning and my first shot at polishing/brushing. Went with the Cape Cod polishing cloth and gray scotch brite method.  Before First; Then After; Then comparing to some original links from when the watch was new to now.       
    • praezis
      Unitas 6376

      By praezis · Posted

      What is this (left of the red line)? hairspring? Frank
    • nickelsilver
      Unitas 6376

      By nickelsilver · Posted

      It's either bent or hung up on something or both. The hexane won't hurt it, and hanging from a balance tack indefinitely won't hurt it.   If the spring is glued to the stud there's a chance that the glue was softened and the outer coil stuck to the stud. Haven't seen that happen, but I suppose it could. Don't know if hexane affects the glue used either.
    • tonydagee
      Unitas 6376

      By tonydagee · Posted

      Hello all. some help required here from the community please. I serviced this movement, which was running reasonably well, but the balance spring which was running healthily before I started, after cleaning in hexane for 30 secs, is all bunched up at the stud. I did store the balalance on a tack thereafter for a day.   could the spring be strained under gravity? I demagnetised of course, and the balance is squeaky clean. some help would be much appreciated. Thanks, Tony G    
×
×
  • Create New...