Jump to content

Longines dial cleaning

jao
 Share

Recommended Posts

jao Member

jao

Posted
Posted

I got this Longines from my brother to try cleaning its dial.

I have looked up the serial number in several places and they all agree it was manufactured in 1947.

As you can see in the pictures, the case and the dial are very corroded and I wonder what can be done to make it look a bit better without making things worse.

After having opened it, I am also concerned about any toxic or radioactive paint on the dial. What would be the best way to deal with this?

Any advice about the questions above would be very welcome.

PXL_20250128_234037797.MP.jpg

PXL_20250209_133606623.MP.jpg

PXL_20250209_132047327.jpg

PXL_20250209_132040258.jpg

Image 2025-02-21 at 07.20.48.jpg

Klassiker Distinguished Member

Klassiker

Posted
Posted

It's important to understand that most of that discolouration isn't dirt, it is irreversible staining caused by chemical processes in the paint and lacquer. No substance in the world can remove it, and an incautious attempt will ruin it. I think it has aged in a dignified manner and would polish the hands and crystal but leave the dial alone. If your brother is not happy with it, then the only real alternatives are replacement or refurbishment.

A lot more can and should in my opinion be done with the case and movement.

  • Like 2
rehajm Super WRT Addict

rehajm

Posted
Posted

…it may difficult for some to appreciate but a dial that has aged as gracefully as this is very desirable by many collectors (as is the ‘suiza’ designation)…and as recommended above the movement, case and a light polish of the hands will freshen everything while still maintaining coherence…this heavy patina Rolex I have is a very modest watch but receives outsized attention at places where expensive watches prevail…

IMG_1320.thumb.jpeg.bbff06089d14394d2a14b56ce4fe7296.jpeg

 

…this is a thread where dial restoration was discussed in detail. Hope it is constructive for your Longines…

  • Like 2
jao Member

jao

Posted
  • Author
Posted

Understood. I shouldn't touch the dial 😃. I'll not.

How about the safety of dealing with it? Should I be extra careful with something or just gloves and mask should be enough to safely deal with this watch?

Klassiker Distinguished Member

Klassiker

Posted
Posted

I may be mistaken, but I don't see any lume on the dial or hands. Just for peace of mind keep your fingers away from your face, wash your hands afterwards and wipe down your work area. You'll be fine.

  • Like 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • transporter
      Smiths rim wind and set

      By transporter · Posted

      Ok, as per pictures I have a smiths rim set and wind on the bench, swimming in oil but all sorted. The fault I have is the mainspring bridle has lost its tab/notch/hook, like a hebdomas pocket watch the mainspring is fitted to a bridal in the barrel which slides around on full wind onto 4 notches in the barrel wall, thus stopping damage to the mainspring by over enthusiastic winding. So my questiion is this, what is the best way to create another hook in the bridal, my thoughts are along the same lines as making a new hole in the mainspring end, annealing etc, but what and how to make the hook?? I have a pair of barrel hook pliers that work great in soft brass but won’t even scratch the bridal, what I don’t want to do is whack a hole into it and not have a hook. the pictures are of the bridal ( broken) and a hebdomas ( complete ) incase you are wondering what I’m on about. And a few of the serivce. Thanks for any advise.
    • zx6rfool
      Replacing, upgrading Ronda 715 Harley?

      By zx6rfool · Posted

      Decided to give the case and bracelet a good cleaning and my first shot at polishing/brushing. Went with the Cape Cod polishing cloth and gray scotch brite method.  Before First; Then After; Then comparing to some original links from when the watch was new to now.       
    • praezis
      Unitas 6376

      By praezis · Posted

      What is this (left of the red line)? hairspring? Frank
    • nickelsilver
      Unitas 6376

      By nickelsilver · Posted

      It's either bent or hung up on something or both. The hexane won't hurt it, and hanging from a balance tack indefinitely won't hurt it.   If the spring is glued to the stud there's a chance that the glue was softened and the outer coil stuck to the stud. Haven't seen that happen, but I suppose it could. Don't know if hexane affects the glue used either.
    • tonydagee
      Unitas 6376

      By tonydagee · Posted

      Hello all. some help required here from the community please. I serviced this movement, which was running reasonably well, but the balance spring which was running healthily before I started, after cleaning in hexane for 30 secs, is all bunched up at the stud. I did store the balalance on a tack thereafter for a day.   could the spring be strained under gravity? I demagnetised of course, and the balance is squeaky clean. some help would be much appreciated. Thanks, Tony G    
×
×
  • Create New...