Jump to content

Recommended Posts

Posted (edited)

The digital revolution has made it so much easier nowadays to make, store and share graphic images - including our beloved watches. What did we do before the internet and digital cameras! I have a Fuji digital camera which I bought quite a few years ago now - it's an "F10" model with 6.3 megapixels - and it takes excellent pictures of watches when the lens setting is switched to "macro". What people tend to forget with digital cameras is that it's not necessarily the number of pixels that gives a good picture - it's also, and more importantly, the quality of the lens. Fuji do excellent lenses so, although this camera is quite old by modern standards, without a lot of add-ons and doodads, the all-important lens quality is excellent.

 

I'm also impressed by the quality of the macro photography in Mark's videos. My own digital video camera - which I use for my YouTube music videos - is a Sony HD. Not an expensive one, nor a particularly sophisticated one. The sound recording quality is poor - but I always record my sound separately in any case - and it's poor in low light - but I always records in full daylight! So it does the job.

Edited by WillFly
Posted

Never a truer word said!

I used to have a Nikon Coolpix with only 2 Mega Pixies and the results were absolutely brilliant on prints up to A4 size all because of a good lens.

Posted

+1 for the Fuji, was my first decent digital camera years ago.

 

Then I upgraded to the Panasonic Lumix TZ7 which was an amazing camera and I still use it when we go away.

 

The Canon DSLR is a fantastic little beast.

 

For audio I use a Samson G-Track usb microphone which is simply excellent as a voice mic but I have also tested it with my guitar and the sound is awesome.

 

I also have a Zoom H4N which I have purchased for the watch repair course I am writing - this will allow me to present the course rather than voiceover.

 

And in case you have not guessed it - I love gadgets :) just wish I could afford more lol.

Posted (edited)

I have two Zoom H2 digital recorders (the old model, not the latest one) which I use for my sound recording. I use mainly one but, occasionally, where I want a nice broad sound spectrum, two. They are absolutely superb and give great sound quality.

Edited by WillFly
Posted

I still have an old Canon Ixus 2.1mp that I occasionally use, it takes excellent pics that look good on screen and print out fine up to A5. Less is often more.

  • 4 months later...
Posted

I use a Olympus C5050 which is about 10 years old, although along with watches and Pocketwatches photography is another passion I do not use my general SLR gear for watch photography the C5050 gives me all I need and as Will has already said pixels are only part of a successful image, correct lighting along with focal and shutter speed settings also figure in the equation..

Best wishes

Darren

Posted

When my building work's done and dusted, I'm thinking of making myself a simple light tent - just to eliminate some of the reflections in shiny cases!

Posted

Hi Will,

 

I actually use a black tile as background and eliminate reflections using a black plastic sheet from an old folder..

 

 

 

post-286-0-14124100-1407344432_thumb.jpg

  • Like 1
Posted

Many Thanks Guys

 

It is much appreciated, I do spend a lot of time on my collection and am trying to work my way up the ladder, but I do enjoy these

and I like to play about with picture and frame them to put on the walls of my work area (spare bedroom)...

 

 

Best Wishes

 

Darren

 

 

 

post-286-0-83042400-1407352475_thumb.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I’ve been playing with a NH35 movement that which has the classic Etachron regulation system and a few balance assemblies as practice. What I’m trying to do is get comfortable with the effect both the stud and regulator pin positions have on rate and positional error. When I install a new balance assembly I install it with the assembly in place  on the cock and cock is attached to base plate. I use the back of the tweezers to push the stud into place and feel the click. However, I noticed that the angle of the stud can be adjusted and what I also noticed is that some movements have the stud carrier arm bent down a little and that changes the angle of the hairspring leaving the stud. This angle effects how the spring goes through the regulator pins and also the spacing of the coils opposite the stud. What I thought I was supposed to do is set the regulator block in the middle of the curve, open the pins, and use the stud angle to center the spring.  Then the stud is set.  Now on all the new NH movements I have seen the angle of the regulator block is about 60 degrees counter clockwise from full open. I watched a video where the author used the regulator pin adjust to adjust rate and position error. When I close down the pins I do notice that the rate increases but also the amplitude drops, the coil spacing changes and hairspring appears slight straighter between the stud and the regulator block. If I open the pins the amplitude comes back, the spring breathes a bit more between the stud and the regulator block and the rate slows.  So, a long post I know but I would really appreciate any advice on how to correctly adjust the etachron system for rate, amplitude and positional error.   
    • Aw come on Andy, it was just a comparison between spending 30 quid and tackling a tricky piece of work. You appeared to be volunteering,  i volunteer for stuff all the time it gets me into all kinds of trouble.
    • It's not really shown here , but the blade flips over, so it faces the other way. The knob and threaded case holder then pushes the caseback seam into the blade. Once the blade starts to penetrate into it, the lever and blade are lifted , which should hopefully pop the back off. A lot of fashion style cases have very tight seams and need a sharp blade to start separating them.  Don't buy the cheaper plastic versions of this tool, the posts with the pins through for blade holder break easily if the apply extra force to blade. 
    • You will still be looking for a balance complete I’m afraid, this is the balance staff, balance wheel and hairspring in one package. Hairspring and the balance wheel are matched in the factory. Whilst we can change a balance staff the hairspring and balance wheel stay together.   Tom
    • The hairspring end has come adrift from the small terminal barrel.  I have tried to remove the taper pin to relocate it, but the task is beyond my skill set, eyes, hands and being in my 70s, probably beyond my life expectancy.  It is not too badly mangled on the end.  On the ebay offer, that really is a bit on the rich side.  I'll keep looking, maybe a good hairspring will turn up with a shot balance staff. As for time spent on knees.  I made up one of these from 3M magnetic tape and a piece of wood.  It works well for magnetic parts. Other things I have suffered with.  I found lubricants so very expensive that I bought some very small syringes and tiny needles.  I just decant a drop into my oiling pots when I start a movement and the remainder keeps really well in the syringes. Finally identifying the correct screw for the part led me to make up the board in the final pic.   Thanks for the info. Kind regards   Chris  
×
×
  • Create New...