Jump to content

Seiko 7S26 - How Much Of A Problem Is A Loose Rotor?

SudoHalt
 Share

Recommended Posts

SudoHalt Member

SudoHalt

Posted
Posted

Hello,

 

I recently bought an SKX011 in a new condition. I noticed that when I put it next to my ear and I quickly move it away and back to my ear, there is some play in the rotor. I tried different ways to make sure it is only the rotor that is loose, and it definitely is. I am in no way confused between the sound of the rotor when it rotates and the sound of the play in the rotor. I heard that this issue is frequently encountered on 7S26 movements, but is it normal?

Blacklab Distinguished Member

Blacklab

Posted
Posted

Pop the back off and have a look. Check the rotor screw is not loose and tighten if reqd. If this doesn't work check to see if the rotor is touching the caseback or movement or has any degree of play. If this is the case you will need to replace the rotor, which are readily available through most of the material houses normally listed as 'Oscillating Weight, Seiko 509.184' priced about £10. These are stamped 7S26B but will fit the 7S26A and most other 7XXX series movements.

  • Like 1
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Leonid
      Rolex cal. 3135 issues

      By Leonid · Posted

      By the way, I opened my watch, looked under a magnifying glass, there is simply no grease, the screws are without traces, the slots are intact.I think it's just a matter of maintenance.there are no rotor marks on the body. And to remove the strap from yours, just press on the 1st side,and slightly move the strap, then on the other side and it will come off.
    • chrisG
      New forum member, new learner

      By chrisG · Posted

      Hi My name is Chris. Just started trying to learn about watch and clock repair as a result of repairing my fathers old 1890s police station clock (about a year ago). The clock was Ok, but having graduated to pocket watches and then wrist watches, despite the really excellent stuff on Youtube, I am struggling a bit.  As a retired engineer, I find the engineering exquisite, but a bit on the fiddly side.  I have done a few practice watches with a little success but failed a few, but have had success with Seiko 7005s, 7009s etc, but have just attempted a citizen 5430.  Nightmare.  My wife thought I had found religion as I spent so much time on my knees with my eyes to the floor looking for springs.  Got through that and found that the balance is shot.  Trying to source one or something that will fit from the citizen range has me totally perplexed.  Tried Ebay, Cousins etc without luck.  Any advice as to alternatives that will fit or alternative sources would be gratefully received.
    • Klassiker
      Typical and max diameter of faceplate for 8mm WW lathe?

      By Klassiker · Posted

      Agreed, this is puzzling. Can you ask questions or inspect the lots before bidding? My Boley & Leinen Reform face plate is dia. 95mm exactly. It's possible that 4 inches is a slightly too large approximation, but why then make the distinction to 3 11/16 for the sake of 8mm? If the larger ones are truly 4" then they will clash with the bed, but then I have no idea which 8mm lathe would take them. All 8mm lathes have spindle height 50mm or less, as far as I know. The spindle height is, as you say, standard 50mm for W.W.
    • Dell
      Patreon Free WRT

      By Dell · Posted

      I have only been a member for six years & I have found this a very friendly forum although I don’t have anything to do with watches not because I don’t like watches but because I have gout in both hands so my dexterity isn’t very good, I restore torsion clocks & occasionally other antique clocks also at 72 my eyes are not what they used to be, that is why I only post on the clock forum & the lathe forum mostly . As others have said Mark it is much appreciated that  you are willing & able to do this. very many Thanks Dell
    • vessel18
      New forum member, new learner

      By vessel18 · Posted

      Ah, this is brilliant, thank you very much!
×
×
  • Create New...