Jump to content

Online purchase - Incoming Certina Bristol


Recommended Posts

Its been tough finding good watches at the right prices on ebay the last few years with even crap watches asking silly money. The shipping costs have also escalated sharply, I particularly dislike the added customs charge fee. I have never been charged anything for used watches I have received thru the post and would definitely prefer paying if and when I am charged.

Anyway, if you are careful and know what you're bidding for there are some bargains to be had. I recently bought this Certina Bristol for not much money and I would like to share some hints about what to look for. This is a 25-66 movement and it built inhouse by Certina and while they are not really cheap when fully working, I believe they are undervalued and are really good value for money,

This is the sellers picture about the watch, a bit of patina and the seconds hand is missing. While the seconds hand alone is not a problem, you need to ask yourself why was it not replaced as someone obviously had the back off to get the seconds hand out? One possibility is the tip of the seconds hand may have broken off. While parts for Certina are available this will add unnecessary problems. Looking at the photo again I can see the remnants of the centre-pinion (whitish dot in the middle).

Capture2.JPG.bebb426029169e4ac380d33974839661.JPG

Another pic from the seller. My guess is that the pinion is good.

Capture6.JPG.5ce918dc0df967993a2b4f6d559d83a4.JPG

Moving on to the backside of the watch. Not much to see here except that the previous watch maker was a bit clumsy opening the caseback.

Capture4.JPG.1104dc43197c193161dbdfb5e8dbd06f.JPG

It still has its original crown which is always nice to see!

Capture3.JPG.d8e23afbb5b3e870f76b457969e01064.JPG

The movement looks pretty clean, sometimes the damage patina on the dial can indicate water damage but since the stem is pretty rust free I would say its just the lacquer breaking down. Nice regulator, sign of a quality watch! I bought the watch about a month back, it has arrived at my friends shop .. I need to collect it.

Capture.thumb.JPG.fd140d829aff1a9b7e2198540bae65a1.JPG

Finally the description. The most important is that balance wheel is good. This does not mean there isn't a problem elsewhere.. It could be a broken mainspring or messed up hairspring. Straightforward and to the point. No mention of being rare or collectible , just needs servicing yadda yadda..

Capture5.JPG.b3dab22a6c8aa00e146d0dc473842c75.JPG

Finally check the seller, In this case its YDL Worldstore.. all good!Capture7.thumb.JPG.24cc25d530ecd638f1c4e41a7b575039.JPG

So I made a bid and won it for USD31+USD15 shipping.. Total USD46. What I get will be an interesting watch with a good quality movement that hopefully a COA will bring back to life. I should have a seconds needle in my box of parts but I might need to change the seconds pinion, we'll see about that. Of course there may be other problems like broken train pivots, cracked jewels etc but that's part of the gamble!

I will probably get the watch back this weekend and will post further here. Stay tuned.

Anilv

 

 

 

Edited by anilv
  • Like 2
Link to comment
Share on other sites

Lucky you it's a 25-66 movement. The second hand wheel is probably broken. But you could still find those wheels pretty easy. They are often broken. Either rust or damage. They are pretty thin and break easily. 

 

Edited by rogart63
  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • The post below contains the link. If you don't already have a discord account it will take you to the registration screen.  Registration is free.   https://www.watchrepairtalk.com/topic/31653-mark/?do=findComment&comment=279066
    • HWGIKE#57 Valex FEF 190 15 jewels Swiss lever full service and repair This one was waiting for a balance staff replacement in my cabinet parts and case cleaned up with a new balance staff and a 4th wheel as the original 4th wheel had a broken pivot for the off center second hand. I never attempted a balance staff replacement before however I received a Bergeon Molfres (i was hunting it for about 2 years) and with the help of it I managed to remove the old staff and riveted the new one in. It also received a new MS, crystal and the hole for the MS arbor was also tightened. With the new MS now it has an acceptable performance meaning that the amplitude goes up to 280 fully wound, has an acceptable beat error and I have the two nice lines but only dial up, dial down is not as nice and I could not figure out as why. I have the two lines but the amplitude is dropping to around 230 and the lines are a bit hairy. Both dial up and dial down the lines just go up and down without seemingly any pattern. I cleaned the movement two times, and then a 3rd time pegged out the main plate and train bridge holes but made no change. Both the HS collet and the roller table was too lose on the new staff... I did not count how many times I took the balance cock off to sort out the HS collet, the roller table and the beat error, somebody before me also shortened the HS by pushing it out a bit and it seems every time somebody is messing with the end of the HS the protruding bit is most of the time twisted bent etc. This one was probably one of the most challenging repair and service. I might take the new MS out and clean it lubricate it as I just pushed the new one in to the barrel from the retaining ring. Plus started to re-read the theory of the escapement and how to analyse the graph on the timing machine: Greiner Chronografic Record manual. I am also thinking to put the watch on a 24 hour long run with the eTimer SW it once helped me to figure out what was wrong with a watch. There is an interesting part of the Greiner record manual talking about the pallets and the end shake of the balance and pallet staff. Maybe this is my issue? Who could that possibly identify? After a few years now I am still without a clue how could watchmakers make parts I can only see with my microscope or how could/can they carry out complicated services impossible to do.. real magic..... .... ..... before I sent this post while the pics were uploading I had an idea, i was browsing the possible outcomes on the timing machine I had one for magnetism..... so I demagnetized the movement and it is not hairy now.... two really nice lines 0.2 ms beat error still a bit wavy, but a lot lot better..... argh....  
    • Hi there, welcome here.  
    • yes the advertising revenue should generate money. The question is how much money? Then as far as the cost of the website goes that's relatively easy to determine? all you would have to do to grasp costs and profitability would be to go to the link below and you can actually get a website for free try it out for free I believe you get no advertising initially. They also talk about that they'll help you out they have marketing tools and some sort of paid subscription or something. So I guess were shopping for a whatever just ask them what would a maybe could use this one as an example in other words it's going to look basically identical to this is going to have advertising a paid subscriptions what's it going to cost? After all they want to sell or give us a message board like this they should bill answer the questions as they're the people who did the software for this. Yes they really said you can have a free discussion group at least to start. https://invisioncommunity.com/ I was curious about the monthly supporter thing where exactly do we find that on this message board? A quick search I'm not finding it so obviously I'm not looking in the right place?
    • Help me out here, but with all the advertising on this site (which I don't mind) wouldn't it pay for itself or even make money for the owner ???
×
×
  • Create New...